EMOSAFE Network Isolators are used in copper-based network connections in private, public, and commercial sectors.
They protect connected equipment against extraneous voltage sources and overvoltage, which can arise from installation errors,
aging components, or moisture at the network interface.
They attenuate low-frequency signal components and thus protect connected equipment from ground loops and other problems.
Overvoltages induced by lightning strike and switching processes can be inductively coupled into network lines. Such overvoltages can be restrained by Network Isolators.
EMOSAFE Network Isolators are primarily used in medical applications.
They conform to the high requirements which IEC 60601-1 places upon galvanic isolation devices in the medical field.
Further information on EMOSAFE Network Isolators:
EMOSAFE Network Isolators
All EMOSAFE Network Isolators have a dielectric strength of at least 4 kV AC, and comply with the requirements of IEC 60601-1.
EN-10Network Isolators
|
Model and Article Number |
Special Features |
AC Dielectric
Strength (kV) |
10/ 100 Mb/s
|
Gigabit Ethernet
|
Typical Return Loss in dB
@ Limiting Frequency |
Typical Insertion Loss in dB
@ Limiting Frequency |
CAD-Model (Step 214)
|
Data Sheet (PDF)
|
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
EN-10HA10009 |
Robust socket connection IP67 protection* Touch protection* Straight internal jack socket |
4 | 12 @ 16 MHz |
0.5 @ 16 MHz |
(891 kB) |
(2 MB) |
||||
EN-10HGA10005 |
4 | 15 @ 100 MHz |
0.8 @ 100 MHz |
(891 kB) |
(2 MB) |
|||||
EN-10VA10008 |
Robust socket connection IP67 protection* Touch protection* Right angled internal jack socket |
4 | 12 @ 16 MHz |
0.5 @ 16 MHz |
(1864 kB) |
(2 MB) |
||||
EN-10VGA10004 |
4 | 15 @ 100 MHz |
0.8 @ 100 MHz |
(1864 kB) |
(2 MB) |
|||||
Z-1A10012 |
IP67 Plug Housing Simple retrofitting of an existing patch cable Protects against water and dust in accordance with IP67 Touch protection Mechanical protection of the mating connection Material: fibreglass-reinforced plastic, black |
(1721 kB) |
(420 kB) |
|||||||
Z-2A10013 |
IP67 Dust Cap Protects against water and dust in accordance with IP67 Mechanical protection of the mating connection Material: fibreglass-reinforced plastic, black |
(1200 kB) |
(2 MB) |
|||||||
Z-EN10-RPA10039 |
19″ Patch Panel Provides mounting locations for 12x EN-10 Network Isolators Material: steel Coating: matt black powder coated |
(65 kB) |
(89 kB) |
– | ||||||
* When used in conjunction with accessories Z-1 or Z-2 |
EN-20 / 30Network Isolators
|
Model and Article Number |
Special Features |
AC dielectric
strength (kV) |
10/ 100 Mb/s
|
Gigabit Ethernet
|
Typical Return Loss in dB
@ Limiting Frequency |
Typical Insertion Loss in dB
@ Limiting Frequency |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
EN-20GA10007 |
Robust plastic housing |
4 | 8 | 1.5 | (306 kB) |
(1 MB) |
||||
EN-30A10001 |
Elegant aluminium housing |
4 | 8 | 1.5 | (138 kB) |
(0.5 MB) |
EN-50EMC-optimized Network Isolators for inclusion in devices |
Model and Article Number |
Special Features |
AC Dielectric
Strength (kV) |
10/ 100 Mb/s
|
Gigabit Ethernet
|
Typical Return Loss in
dB @ 100 MHz |
Typical Insertion Loss
in dB @ 100 MHz |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
EN-50HG-SA10205 |
Y-Capacitors and rear-end ground terminal for electromagnetic suppression Horizontal internal outlet |
4 | 8 | 1.5 | (262 kB) |
(1.9 MB) |
||||
EN-50VG-SA10201 |
Y-Capacitors and rear-end ground terminal for electromagnetic suppression Vertical internal outlet |
4 | 8 | 1.5 | (247 kB) |
(1.9 MB) |
||||
EN-50HG-YA10200 |
As per EN-50HG-S Y-Con® connect interface for improved retaining strength and reduced accidental touch risk |
4 | 8 | 1.5 | (278 kB) |
(1.9 MB) |
||||
Z-EN50-BP00396 |
Bezel for EN-50 Network Isolators | (33 kB) |
see EN-50 Data Sheet |
|||||||
Z-EN50-SLBP00397 |
Safety Bezel for EN-50 Network Isolators with touch protection and safety locking | (123 kB) |
see EN-50 Data Sheet |
|||||||
Z-EN50-RPA10040 |
19″ Patch Panel, provides mounting locations for twelve EN-50 Network Isolators Material: matt black powder coated steel |
(76 kB) |
(75 kB) |
EN-60High Performance
|
Model and Article Number |
Special Features |
AC Dielectric
Strength (kV) |
10/ 100/ 1000 Mb/s
|
TVS-Diodes
|
Typical Return Loss in
dB @ 100 MHz |
Typical Insertion Loss in
dB @ 100 MHz |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
EN-60KDSA10043 |
Class D Performance Configurable cable length Keystone module High dielectric strength |
6 | 17 | 0.7 | (346 kB) |
(1.6 MB) |
||||
Z-5-KMBA10064 |
Universal mounting bracket for Network Isolators (or other devices) with Keystone interface | (50 kB) |
(328 kB) |
EN-65Installation Network Isolator with Cable |
Model and Article Number |
Special features |
AC Dielectric
Strength in kV |
TVS-Diodes
|
10/100/1000 Mbit/s
|
Typical Return Loss (dB)
@ 100 MHz |
Typical Insertion Loss (dB)
@ 100 MHz |
CAD-Modell
(Step 214) |
Data Sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
SnapFit |
EN-65SA10069 |
High performance. Physical interface for use with EMOSAFE SnapFit accessories | 5.0 | 20 | 0.5 | (1 MB) |
(3.3 MB) |
|||
Keystone |
EN-65KA10068 |
High performance. For use in Keystone-compatible outlets. | 5.0 | 20 | 0.5 | (1 MB) |
(3.3 MB) |
|||
Snapfit Installation frame |
Z-3-SF-INTA10057 |
Housing assembly for flush mounting Two M2.5 brass inserts Two snap-fit positions Material: polyamide, black |
(60 KB) |
(3.3 MB) |
||||||
Snapfit Installation frame |
Z-4-SF-EXTA10058 |
Protruding housing assembly Two snap-fit positions Material: polyamide, black |
(31 KB) |
(3.3 MB) |
||||||
Keystone Mounting Bracket |
Z-5-KMBA10064 |
Universal Keystone Mounting Bracket for Network Isolators featuring Keystone interfaces (as well as all other Keystone-compatible modules) | (50 KB) |
(328 KB) |
EN-6610GB Model Installation Network Isolator with Cable |
Model and Article Number |
Special features |
AC Dielectric
Strength in kV |
TVS-Diodes
|
10/100/1000/10000
Mbit/s
|
Typical Return Loss (dB)
@ 100 MHz |
Typical Insertion Loss (dB)
@ 100 MHz |
CAD-Modell
(Step 214) |
Data Sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
SnapFit |
EN-66SA10075 |
Ultra-High performance. Physical interface for use with EMOSAFE SnapFit accessories | 5.0 | 20 | 0.5 | (1 MB) |
(3.3 MB) |
|||
Keystone |
EN-66KA10076 |
Ultra-High performance. For use in Keystone-compatible outlets. | 5.0 | 20 | 0.5 | (1 MB) |
(3.3 MB) |
|||
Stand alone cable |
EN-66eA10074 |
Ultra-High performance. For use in Keystone-compatible outlets. | 5.0 | 20 | 0.5 | (1 MB) |
(3.3 MB) |
|||
Snapfit Installation frame |
Z-3-SF-INTA10057 |
Housing assembly for flush mounting Two M2.5 brass inserts Two snap-fit positions Material: polyamide, black |
(60 KB) |
(3.3 MB) |
||||||
Snapfit Installation frame |
Z-4-SF-EXTA10058 |
Protruding housing assembly Two snap-fit positions Material: polyamide, black |
(31 KB) |
(3.3 MB) |
||||||
Keystone Mounting Bracket |
Z-5-KMBA10064 |
Universal Keystone Mounting Bracket for Network Isolators featuring Keystone interfaces (as well as all other Keystone-compatible modules) | (50 KB) |
(328 KB) |
EN-70Ultra-compact
|
Model and Article Number |
Special Features |
AC Dielectric
Strength in kV |
TVS-Diodes
|
10/ 100/ 1000 Mb/s
|
Typical Return Loss in dB
@ 100 MHz |
Typical Insertion Loss in dB
@ 100 MHz |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
Standard |
EN-70eA10053 |
Economy plug-in isolator Grey cap |
4.6 | 17 | 1.0 | (194 kB) |
(1.9 MB) |
|||
EN-70HDA10054 |
High performance plug-in isolator Black cap |
5 | 20 | 0.7 | (194 kB) |
(1.9 MB) |
||||
Keystone |
EN-70HD-KA10059 |
High performance isolators for assembly into Keystone-compatible electrical outlets |
5 | 20 | 0.7 | (235 kB) |
(1.9 MB) |
|||
EN-70VD-KA10060 |
5 | 20 | 0.7 | (211 kB) |
(1.9 MB) |
|||||
SnapFit |
EN-70HD-SA10055 |
High performance isolators suitable for use with EMOSAFE SnapFit installation frame accessories | 5 | 20 | 0.7 | (187 kB) |
(1.9 MB) |
|||
EN-70VD-SA10056 |
5 | 20 | 0.7 | (94 kB) |
(1.9 MB) |
|||||
SnapFit Installation Frame |
Z-3-SF-INTA10057 |
Housing assembly for flush mounting Two M2.5 brass inserts Two snap-fit positions Material: polyamide, black |
(60 kB) |
(1.9 MB) |
||||||
SnapFit Installation Frame |
Z-4-SF-EXTA10058 |
Protruding housing assembly Two snap-fit positions Material: polyamide, black |
(31 kB) |
(1.9 MB) |
||||||
Mounting Bracket |
Z-5-KMBA10064 |
Universal mounting bracket for Network Isolators (or other devices) with Keystone interfaces | (50 kB) |
(328 kB) |
EN-85eNetwork Isolator
|
Model and Article Number |
Special Features |
AC Dielectric
Strength in kV |
Gigabit Ethernet
|
TVS-Diodes
|
Typical Return Loss
in dB @ 100 MHz |
Typical Insertion Loss
in dB @ 100 MHz |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
EN-85eA10067 |
Network Isolator with straight cable outlet and Overtension Auto-Release (OTAR) | 4.6 | – | 20.0 | 0.4 | (1.1 MB) |
(2.4 MB) |
EN-100Network Isolators
|
Model and Article Number |
Special Features |
AC Dielectric
Strength in kV |
TVS-Diodes
|
Gigabit Ethernet
|
Typical Return Loss
in dB @ 100 MHz |
Typical Insertion Loss
in dB @ 100 MHz |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
Solderable |
EN-100CA10051 |
Milling of PCB is not required Edge soldering receptacles for manual assembly Solderable |
4.6 | 17 | 0.8/td> | (125 kB) |
(2.3 MB) |
|||
Solderable |
EN-100SA10048 |
Extra-short length between inputs and outputs Edge soldering receptacles for manual assembly Solderable |
4.6 | 17 | 0.8 | (100 kB) |
(2.3 MB) |
|||
Pluggable/Solderable |
EN-100LA10050 |
Extra-short length between inputs and outputs Upwards-facing pins In-circuit pluggable and solderable |
4.6 | 17 | 0.8 | (131 kB) |
(2.3 MB) |
|||
Pluggable/Solderable |
EN-100TA10049 |
Extra-short length between inputs and outputs Downwards-facing pins In-circuit pluggable and solderable |
4.6 | 17 | 0.8 | (132 kB) |
(2.3 MB) |
Working together with you, we can develop and design a Network Isolator that is optimally tailored to your specific requirements; including the construction of all molds and tools necessary for production and assembly, the preparation of all product-accompanying documents, creating packaging designs, as well as taking care of any approvals you require for your product.Profit from our versatile and extensive experience in the field of product development!
Simply call us for obligation-free advice and information. We will be happy to provide you with technical support.972-677-3667
EN-1005+High Performance
|
Model and Article Number |
Special Features |
AC Dielectric
Strength in kV |
Gigabit Ethernet
|
TVS-Dioden
|
Typical Return Loss
in dB @ 100 MHz |
Typical Insertion Loss
in dB @ 100 MHz |
CAD-Model
(Step 214) |
Data sheet
(PDF) |
Configuration |
---|---|---|---|---|---|---|---|---|---|---|
EN-1005+A10065 |
High Performance Network Isolator | 5.0 | 20.0 | 0.7 | (468 KB) |
(2 MB) |
||||
Z-6WA10070 |
Wall Mounting Plate for any flat surface | (85 KB) |
(2 MB) |
|||||||
Z-6RA10071 |
Adapter for mounting on an EN 50022 standard 35 mm DIN rail | (204 KB) |
(2 MB) |
|||||||
Customer-specific
|
Model | Transmission Rate | Special Features | |||||||
R&M SafeLine | 10/100/1000 Mb/s | Fits into wall outlet sockets with R&M module bays. Only available from R&M (www.rdm.com) |
||||||||
Custom Types | 10/100/1000 Mb/s | According to your specifications |
Technology
EMOSAFE Network Isolators operate based on the principle of electromagnetic induction. Because of this transmission principle, Network Isolators do not require separate power supplies. There are no software drivers to be installed. Transmitter modules developed especially for our Network Isolators reach dielectric strengths of up to 6000 V AC and 8500 V DC (model dependent); and with a three-layer insulation system, conform to the highest safety requirements. At the same time they facilitate a particularly low-loss signal transfer, so that the usual maximum Ethernet network path length of 100 meters can be fully utilised in most cases without leading to a reduction in data throughput.
Further questions regarding the technology and the operation of Network Isolators are answered on our FAQ.
Detailed information on individual products can be found in the product-related documents within the Network Isolators section.
Scopes of Application
-
- Medical electrical devices whose operation is permitted only when existing signal interfaces present a standards-compliant means of separation. Hence the frequently used term “medical network isolator”.
-
- Sensitive measuring and monitoring devices in electrical testing laboratories, which are connected through an Ethernet network to a control centre, and need to be protected from transients and potential differences.
-
- Computer systems which are electrically connected over long distances via Ethernet cabling, where potential equalising currents need to be prevented.
-
- Audio applications, to reduce the transmission of low frequency alternating currents (AC hum) over the network connection.
-
- Applications where valuable or especially vulnerable devices need to be protected from overvoltage and line noise from peripheral network equipment.
Quality
Both the development and the production processes of our Network Isolators are certified in accordance with ISO 9001 and DIN EN ISO 13485.
Prior to delivery, each EMOSAFE Network Isolator is individually tested, to measure, record, and ensure the compliance of their dielectric withstand strengths.
To guarantee optimal transmission quality, each EMOSAFE Network Isolator is additionally subjected to a comprehensive quality inspection. This inspection ensures that the attained values relating to transmission performance (specifically insertion losses, return losses, and near end crosstalk values) all meet or exceed the specified requirements.
Do you have any further queries regarding our EMOSAFE Network Isolators? Answers to the most frequently asked questions can be found in our FAQ.
We are happy to personally answer specialised questions, simply call us on the number below.
972-677-3667
Standard Conformity and Certificates
EMO Systems GmbH confirms the conformity with the requirements of the standards and directives to be applied, in particular IEC 60601-1, with a CE-declaration.
Based on the approval by Underwriters Laboratories Inc. (UL) as Recognized Component E249126, our EMOSAFE Network Isolators are also suitable for application in the North American markets.
As part of the UL approval test process, our Network Isolators are examined for conformity with IEC 60601-1-1.
EMO Systems GmbH is also certified in accordance with DIN EN ISO 9001 and DIN EN ISO 13485 by the international certification organization TÜV SÜD.
This means that our development processess (including those contracted to us), our production processes, as well as our sales and services are all controlled and directed by an underlying quality management system, which in turn is tested for compliance to these standards on a regular basis.
Declaration of Conformity for Network Isolators |
UL Certificate |
TÜV SÜD Certificate DIN EN ISO 9001 |
TÜV SÜD Certificate DIN EN ISO 13485 |
---|---|---|---|
(105 kB) |
(250 kB) |
(190 kB) |
(386 kB) |